ASTM B179-11 Historical Standard: B969/B969M Specification for Aluminum-Alloy Castings Produced by Squeeze Casting, E716 Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition
ASTM B179 - 11e1 Standard Specification for Aluminum 2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ASTM Standards. B26/B26M Specification for Aluminum-Alloy Sand Castings. B85/B85M Specification for Aluminum-Alloy Die Castings. B108/B108M Specification for Aluminum-Alloy Permanent Mold Castings. B618/B618M Specification
The ingots or molten metal shall conform to the chemical composition limits specified.</p> Adopted:2006-09-01 Withdrawn:2009-11-15 ICS:77.120.10 - Aluminium og aluminiumlegeringer 904.02.02 - Volume 02.02 - Aluminum and Magnesium Alloys
ASTM International - ASTM B179-11 - Standard Specification May 01, 2011 · ASTM International - ASTM B179-11 1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1. ASTM B179-06. September 1, 2006
ASTM International - ASTM B179-11e1 - Standard ASTM International - ASTM B179-11e1 1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1. ASTM B179-06
This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The material shall be of uniform quality and shall be free from dross, slag, and other harmful contamination. The ingots or molten metal shall conform to the chemical composition
ASTM-B179, 1996 - MADCADASTM B179-96 Historical Standard: E716 Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spectrochemical Analysis B179-06 Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes.
Aluminum and Aluminum Alloys - NISTAluminum and Aluminum Alloys / 355 Table 2 Strength ranges of various wrought aluminum alloys Aluminum Type of Tensile Association alloy Strengthening strength range series composition method MPa ksi 1xxx Al Cold work 70175 1025 2xxx Al-Cu-Mg Heat treat 170310 2545 (12.5% Cu) 2xxx Al-Cu-Mg-Si Heat treat 380520 5575 (36% Cu)
isted herein are designations and chemical composition limits for wrought aluminum and wrought aluminum alloys registered with The Aluminum Association. Numerical designations are assigned in accordance with the RecommendationInternational Designation System for Wrought Aluminum and Wrought Aluminum Alloys, which is printed on pages 28
Japanese Industrial Standards Data Aluminum alloy die Japanese Industrial Standards. JIS H 5302:2006. Aluminum alloy die casting Preface. The chart below is from the Japanese Industrial Standards and is based on the information contained in ISO/FDIS 3522:Aluminium and aluminium alloys-Castings-Chemical composition and mechanical properties published in 2006.
Standard Specication for Aluminum-Alloy Die CastingsAluminum-Alloy Die Castings1 in Cast Form for Determination of Chemical Composition6 1 This specication is under the jurisdiction of ASTM Committee B07 on Light Metals and Alloys and is the direct responsibility of Subcommittee B07.01 on Aluminum Alloy Ingots and Castings.
Aluminum and Aluminum Alloys for Determination of Chemical Composition by SpectrochemicalAnalysis E1251 Test Method forAnalysis ofAluminum andAlumi-numAlloys byAtomic Emission Spectrometry 2.2 ANSIStandard:H35.1/H35.1(M) American National Standard Alloy and Temper Designation Systems forAluminum3 2.3 AluminumAssociationsStandard:
UNS Number A2 Aluminum and Aluminum AlloysUNS No:Description:Brand/Trp:AA Eq. ASTM Eq:UNS A03081:Aluminum Goundry Alloy. Ingot:AA 308.1:UNS A03082:Aluminum Goundry Alloy. Ingot:AA 308.2:UNS A03190 ASTM B179-06 - AlumachineAug 18, 2019 · August 18, 2019 Aluminum Machinery Total Solution Provider Blog. ASTM B179-06 Aluminum alloys chemical composition ASTM B179-06 Aluminum alloys chemical composition ALUMINIUM ALLOYS CHEMICAL COMPOSITION% ASTM B179-06 (Si) (Fe) (Cu ) (Mn) (Mg) Cr) (Ni) (Zn) (Ti) (Sn) (AL) A356.1 6.5-7.5 0.15 Max 0.20Max 0.10 Max 0.3-0.45 0.10 Max 0.20 Max